2 Drums ONLY! Change of mind on colour. Massive Savings!

Tinted to: Colorbond "PAPERBARK

Taubmans All Weather Low Sheen Exterior Paint

Just like the name suggests, Taubmans’ All Weather exterior paint provides protection in all weather conditions. It prevents blistering, flaking, or peeling of paint if applied correctly. Maximum protection from dirt and stains ensures that your exteriors will remain looking as good as new for longer. The paint is formulated to create a strong protective shield, allowing you to easily clean it without compromising the quality of the paint. 

Features 

Advanced UV protection against chalking

Chalking happens when a fine powder appears on the surface of a paint film due to the degradation of the paint. It is usually caused by exposure to UV light or other forms of radiation. All Weather is formulated to be highly durable and protect against UV damage and chalking. 

Protection against mould and mildew

Taubmans All Weather inhibits the growth of mould and mildew. Mould and mildew can be harmful to health, especially if you have asthma or other allergies. All Weather’s special anti-mould and mildew formula ensures that you’ll be protected. 

Lifetime guarantee

Taubmans All Weather has a lifetime guarantee against blistering, flaking, or peeling if applied correctly. Taubmans lifetime guarantee gives you peace of mind that you can rely on its protection for longer.

Self priming 

All Weather’s self-priming formula means that you don’t have to worry about applying a separate primer. It helps to seal in underlying liquids, form a surface for paint to adhere to; and provide a uniform surface to improve the paint's appearance.

Washable and dirt resistant

Taubmans Nanoguard technology provides a protective shield so dirt can be easily washed away without compromising the quality of the paint or damaging the finish. 

What textures is Taubmans All Weather available in?

• Low-sheen

Ideal for: Weatherboard, cement render, fibrous cement, brick, fences, pergolas and outdoor timber furniture. Suitable for the collection of drinking water. Gloss level 10-15%.

Surface Preparation

• Surfaces must be clean, dry and free from all surface contamination.
• Treat mould with bleach then rinse with fresh water.

New Work

• Timber - Weathered (greyed) timber MUST be sanded to the original timber surface. Tannin rich timbers such as cedar should be primed with Taubmans 3 in 1 Prep or a suitable Taubmans oil based wood primer.
• Galvanised Iron - Thoroughly degrease new surfaces. Weathered surfaces should be thoroughly cleaned before painting.
  For structural galvanised iron, abrade with 240 grade paper to remove chemical treatments and allow full adhesion.
  Cement Render/Concrete - Allow masonry, cement render and mortar to cure for 28 days before painting.
  Steel - Remove rust and prime with a suitable Taubmans iron & steel primer or White Knight Rust Guard® Metal Primer.
  ZINCALUME® STEEL - Wash with water and mild detergent. Surface must be clean and dry. Apply one coat of Taubmans 3 in 1 Prep.

Repaint

• Remove all loose and flaking paint. Spot bare areas with Taubmans All Weather Exterior Low Sheen or the appropriate primer. Apply Taubmans 3 in 1 Prep to aged enamel systems to provide intercoat adhesion. Thoroughly sand new or unweathered Colorbond.® 

After Painting

• Avoid exposure to steam for 48 hours. Surface may be washed after 7 days, but always avoid abrasive cleaners.
  
  
• Coats
  Minimum two coats. Apply a third coat for superior performance (depending on substrate - coverage will be lower on rough or absorbent surfaces.
  
  
• Clean Up
  Water: Scrape excess paint from equipment into a separate container. Wash up with water. Do not dispose of paint or wash water into drains or sewers.
  
  
• Coverage
  Up to 16 square metres per litre (depending on substrate).
  
  
• Recoat
  2 hours at 25°C (allow 4 hours in cold or humid areas)

• Stirring
  Stir paint with a wide flat stirrer in a circular lifting motion for at least 5 minutes before use. It is a requirement to stir paint before use to ensure that the colour tints are dispersed evenly throughout the paint. Continue stirring at regular intervals during application. Where more than one can of the same colour and product is required for a job, mix the contents of all the cans together to ensure colour consistency.

Do not use at temperatures below 10°C, above 35°C or when humidity is excessive.